新闻中心
产品分类
友情链接
|
|
首页 > 供应产品 > 施耐德 ATV71HU75N4Z 7.5KW 变频器
施耐德 ATV71HU75N4Z 7.5KW 变频器
产品系列 | Altivar 71 |
---|
产品类型 | 变频器 |
---|
应用领域 | 复杂的高功率机械 |
---|
组件名称 | ATV71 |
---|
电动机功率 (kW) | 7.5 kW, 3 phases at 380...480 V |
---|
电机功率 | 10 hp, 3 phases at 380...480 V |
---|
maximum motor cable length | 50 m shielded cable 100 m unshielded cable |
---|
power supply voltage | 380...480 V - 15...10 % |
---|
电网相数 | 3 相 |
---|
线路电流 | 22.2 A for 480 V 3 phases 7.5 kW / 10 hp 27 A for 380 V 3 phases 7.5 kW / 10 hp |
---|
EMC 滤波器 | 集成的 |
---|
组装方式 | 带散热片 |
---|
变量 | 无外拉面板 |
---|
视在功率 | 17.8 kVA at 380 V 3 phases 7.5 kW / 10 hp |
---|
预期线路Isc | 22 kA for 3 phases |
---|
额定输出电流 | 14 A at 4 kHz 460 V 3 phases 7.5 kW / 10 hp 17.6 A at 4 kHz 380 V 3 phases 7.5 kW / 10 hp |
---|
*大瞬变电流 | 26.4 A for 60 s 3 phases 7.5 kW / 10 hp 29 A for 2 s 3 phases 7.5 kW / 10 hp |
---|
输出频率 | 0.1…599 Hz |
---|
额定开关频率 | 4 kHz |
---|
开关频率 | 1...16 kHz adjustable 4...16 kHz with derating factor |
---|
异步电机控制配置文件 | 电压/频率比例 (2或5点) ENA系统(能量适配系统)的不平衡机器 带传感器的通量矢量控制(FVC) (电流矢量) 无传感器的通量矢量控制(SFVC) (电压或电流矢量) |
---|
极化方式 | No impedance for Modbus |
---|
补充信息产品功能 | 同步电机 异步电机 |
---|
power supply voltage limits | 323…528 V |
---|
power supply frequency | 50...60 Hz - 5...5 % |
---|
power supply frequency limits | 47.5...63 Hz |
---|
速度范围 | 1…100 for asynchronous motor in open-loop mode, without speed feedback 1…1000 for asynchronous motor in closed-loop mode with encoder feedback 1…50 for synchronous motor in open-loop mode, without speed feedback |
---|
速度精度 | +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn +/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn |
---|
扭矩精度 | +/- 15 % in open-loop mode, without speed feedback +/- 5 % in closed-loop mode with encoder feedback |
---|
瞬时过转矩 | 170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes 220 % of nominal motor torque +/- 10 % for 2 s |
---|
制动力矩 | <= 150 % with braking or hoist resistor 30 % without braking resistor |
---|
同步电机控制配置模式 | 矢量控制无速度反馈 |
---|
调节回路 | PI监控 |
---|
电机滑差补偿 | 可抑制 可调 不可用电压/频率比(2 或 5 点) 自动 无论负载情况 |
---|
diagnostic | 1 LED (red) for drive voltage |
---|
输出电压 | <= 电源电压 |
---|
隔离 | 电源与控制之间的电路 |
---|
type of cable for mounting in an enclosure | With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR |
---|
电气连接 | Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) Terminal, clamping capacity: 6 mm², AWG 8 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) |
---|
紧固扭矩 | 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) 3 N.m, 26.5 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) |
---|
电源 | Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection Internal supply: 24 V DC (21…27 V), <200 mA, protection type: overload and short-circuit protection |
---|
模拟量输入数量 | 2 |
---|
模拟量输入类型 | AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits |
---|
input sampling time | 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s) 2 ms +/- 0.5 ms (Al2) - analog input(s) 2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s) 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input(s) |
---|
响应时间 | <= 100 ms in STO (Safe Torque Off) AO1 2 ms, tolerance +/- 0.5 ms for analog output(s) R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s) R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s) |
---|
absolute accuracy precision | +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C +/- 0.6 % (AI2) for a temperature variation 60 °C +/- 1 % (AO1) for a temperature variation 60 °C |
---|
线性度误差 | +/- 0.15 % of maximum value (AI1-/Al1+, AI2) +/- 0.2 % (AO1) |
---|
模拟量输出数量 | 1 |
---|
模拟量输出 型号 | AO1 software-configurable logic output 10 V 20 mA AO1 software-configurable current 0...20 mA, impedance: 500 Ohm, resolution 10 bits AO1 软件-可配置电压 0...10 V DC, 阻抗: 470 Ω, 分辨率 10 bits |
---|
离散量输出数量 | 2 |
---|
输出型式 | Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles Configurable relay logic: (R2A, R2B) NO - 100000 cycles |
---|
*小开关电流 [Imin] | 3 mA at 24 V DC for configurable relay logic |
---|
*大开关电流 | R1, R2: 2 A 在…上 250 V AC 感性负载 量, cos phi = 0.4 R1, R2: 2 A 在…上 30 V DC 感性负载 量, cos phi = 0.4 R1, R2: 5 A 在…上 250 V AC 阻性(负载) 量, cos phi = 1 R1, R2: 5 A 在…上 30 V DC 阻性(负载) 量, cos phi = 1 |
---|
离散量输入数量 | 7 |
---|
数字量输入类型 | LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm LI6: switch-configurable PTC probe 0…6, impedance: 1500 Ohm PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to ISO 13849-1 level d |
---|
离散量输入逻辑 | Negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1) Positive logic (source) (LI1...LI5), < 5 V (state 0), > 11 V (state 1) Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1) Positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1) |
---|
加速和减速倾斜 | 从 0.01 至 9000 s 独立线性可调 S, U 或自定义 超出刹车能力时的坡道自适应,采用电阻 |
---|
制动至停止 | 采用直流注入 |
---|
保护类型 | Against exceeding limit speed: drive Against input phase loss: drive Break on the control circuit: drive Input phase breaks: drive Line supply overvoltage: drive Line supply undervoltage: drive Overcurrent between output phases and earth: drive Overheating protection: drive Overvoltages on the DC bus: drive Short-circuit between motor phases: drive Thermal protection: drive Motor phase break: motor Power removal: motor Thermal protection: motor |
---|
绝缘电阻 | > 1 mOhm 500 V DC for 1 minute to earth |
---|
频率分辨率 | Analog input: 0.024/50 Hz Display unit: 0.1 Hz |
---|
通讯端口协议 | 串口Modbus CANopen |
---|
端口类型 | 1 RJ45 (on front face) for Modbus 1 RJ45 (on terminal) for Modbus Male SUB-D 9 on RJ45 for CANopen |
---|
物理接口 | 2-wire RS 485 for Modbus |
---|
传输帧 | RTU for Modbus |
---|
传输率 | 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal 9600 bps, 19200 bps for Modbus on front face 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen |
---|
数据格式 | 8 bits, 1 stop, even parity for Modbus on front face 8 bits, odd even or no configurable parity for Modbus on terminal |
---|
地址数 | 1…127 for CANopen 1…247 for Modbus |
---|
访问方法 | Slave CANopen |
---|
标识 | CE |
---|
|